View TDA6650TDA6651_291570.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer for hybrid terrestrial tuner (digital and analog)
Rev. 04 -- 8 December 2004 Product data sheet
1. General description
The TDA6650TT; TDA6651TT is a programmable 3-band mixer/oscillator and low phase noise PLL synthesizer intended for pure 3-band tuner concepts applied to hybrid (digital and analog) terrestrial and cable TV reception. The device includes three double balanced mixers for low, mid and high bands, three oscillators for the corresponding bands, a switchable IF amplifier, a wideband AGC detector and a low noise PLL synthesizer. The frequencies of the three bands are shown in Table 1. Two pins are available between the mixer output and the IF amplifier input to enable IF filtering for improved signal handling and to improve the adjacent channel rejection.
Table 1: Band Low Mid High
[1]
Recommended band limits in MHz for PAL and DVB-T tuners [1] RF input Min 44.25 157.25 443.25 Max 157.25 443.25 863.25 Oscillator Min 83.15 196.15 482.15 Max 196.15 482.15 902.15
RF input frequency is the frequency of the corresponding picture carrier for analog standard.
The IF amplifier is switchable in order to drive both symmetrical and asymmetrical outputs. When it is used as an asymmetrical amplifier, the IFOUTB pin needs to be connected to the supply voltage VCCA. Five open-drain PMOS ports are included on the IC. Two of them, BS1 and BS2, are also dedicated to the selection of the low, mid and high bands. PMOS port BS5 pin is shared with the ADC. The AGC detector provides a control that can be used in a tuner to set the gain of the RF stage. Six AGC take-over points are available by software. Two programmable AGC time constants are available for search tuning and normal tuner operation. The local oscillator signal is fed to the fractional-N divider. The divided frequency is compared to the comparison frequency into the fast phase detector which drives the charge pump. The loop amplifier is also on-chip, including the high-voltage transistor to drive directly the 33 V tuning voltage without the need to add an external transistor. The comparison frequency is obtained from an on-chip crystal oscillator. The crystal frequency can be output to the XTOUT pin to drive the clock input of a digital demodulation IC.
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
Control data is entered via the I2C-bus; six serial bytes are required to address the device, select the Local Oscillator (LO) frequency, select the step frequency, program the output ports and set the charge pump current or select the ALBC mode, enable or disable the crystal output buffer, select the AGC take-over point and time constant and/or select a specific test mode. A status byte concerning the AGC level detector and the ADC voltage can be read out on the SDA line during a read operation. During a read operation, the loop `in-lock' flag, the power-on reset flag and the automatic loop bandwidth control flag are read. The device has 4 programmable addresses. Each address can be selected by applying a specific voltage to pin AS, enabling the use of multiple devices in the same system. The I2C-bus is fast mode compatible, except for the timing as described in the functional description and is compatible with 5 V, 3.3 V and 2.5 V microcontrollers depending on the voltage applied to pin BVS.
2. Features
s Single-chip 5 V mixer/oscillator and low phase noise PLL synthesizer for TV and VCR tuners, dedicated to hybrid (digital and analog) as well as pure digital applications (DVB-T) s Five possible step frequencies to cope with different digital terrestrial TV and analog TV standards s Eight charge pump currents between 40 A and 600 A to reach the optimum phase noise performance over the bands s Automatic Loop Bandwidth Control (ALBC) sets the optimum phase noise performance for DVB-T channels s I2C-bus protocol compatible with 2.5 V, 3.3 V and 5 V microcontrollers: x Address + 5 data bytes transmission (I2C-bus write mode) x Address + 1 status byte (I2C-bus read mode) x Four independent I2C-bus addresses. s Five PMOS open-drain ports with 15 mA source capability for band switching and general purpose; one of these ports is combined with a 5-step ADC s Wideband AGC detector for internal tuner AGC: x Six programmable take-over points x Two programmable time constants x AGC flag. s In-lock flag s Crystal frequency output buffer s 33 V tuning voltage output s Fractional-N programmable divider s Balanced mixers with a common emitter input for the low band and for the mid band (each single input) s Balanced mixer with a common base input for the high band (balanced input) s 2-pin asymmetrical oscillator for the low band s 2-pin symmetrical oscillator for the mid band s 4-pin symmetrical oscillator for the high band
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
2 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
s Switched concept IF amplifier with both asymmetrical and symmetrical outputs to drive low impedance or SAW filters i.e. 500 /40 pF.
3. Applications
For all applications, the recommendations given in the latest application note CC0419 must be used.
3.1 Application summary
s s s s Digital and analog terrestrial tuners (OFDM, PAL, etc.) Cable tuners (QAM) Digital TV sets Digital set-top boxes.
4. Ordering information
Table 2: Ordering information Package Name TDA6650TT; TDA6651TT TSSOP38 Description plastic thin shrink small outline package; 38 leads; body width 4.4 mm; lead pitch 0.5 mm Version SOT510-1 Type number
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
3 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
5. Block diagram
IFFIL1 n.c. 21 (18) VCCA 26 (13) 6 (33) IFFIL2 7 (32) 28 (11) IF AMP IFOUTA IFOUTB 27 (12) (30) 9 AGC
TDA6650TT (TDA6651TT)
AGC DETECTOR AGC flag AL0, AL1, AL2 ATC (10) 29 (1) 38
IFGND LOSCIN LOSCOUT
LBIN
4 (35)
LOW INPUT
BS1
LOW MIXER
BS1
LOW OSCILLATOR
(2) 37
(5) 34 MBIN 3 (36) MID INPUT BS2 MID MIXER BS2 MID OSCILLATOR (4) 35
MOSCIN1 MOSCIN2
HBIN1 HBIN2
1 (38) 2 (37) HIGH INPUT BS1 . BS2 HIGH MIXER BS1 . BS2 HIGH OSCILLATOR
(9) 30 (8) 31 (7) 32 (6) 33
HOSCIN1 HOSCOUT1 HOSCOUT2 HOSCIN2 OSCGND
RFGND
5 (34)
(3) 36
VCCD
24 (15)
N [14:0]
R0, R1, R2
OUTPUT BUFFER
(21) 18
XTOUT
FRACTIONAL DIVIDER
FRACTIONAL CALCULATOR
PHASE COMPARATOR
T0, T1, T2
LOOP AMP
(17) 22
VT
XTAL1 XTAL2 SCL SDA AS BVS
19 (20) 20 (19) 15 (24) 16 (23) 17 (22) 13 (26) I2C-BUS TRANSCEIVER AGC LOCK DETECTOR CRYSTAL OSCILLATOR REFERENCE DIVIDER CHARGE PUMP (16) 23 CP
T0, T1, CP0, CP1, T2 CP2 FRACTIONAL SPURIOUS COMPENSATION (14) 25 PLLGND
BAND SWITCH OUTPUT PORTS 14 (25) ADC/ BS5 BS4 8 (31) 10 (29) 11 (28) 12 (27)
BS5BS1
POR
ADC
fce723
BS3 BS2
BS1
The pin numbers in parenthesis represent the TDA6651TT.
Fig 1. Block diagram
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
4 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
6. Pinning information
6.1 Pin description
Table 3: Symbol HBIN1 HBIN2 MBIN LBIN RFGND IFFIL1 IFFIL2 BS4 AGC BS3 BS2 BS1 BVS ADC/BS5 SCL SDA AS XTOUT XTAL1 XTAL2 n.c VT CP VCCD PLLGND VCCA IFOUTB IFOUTA IFGND HOSCIN1 HOSCOUT1 HOSCOUT2 HOSCIN2
9397 750 14178
Pin description Pin TDA6650TT 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 TDA6651TT 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 high band RF input 1 high band RF input 2 mid band RF input low band RF input RF ground IF filter output 1 IF filter output 2 PMOS open-drain output port 4 for general purpose AGC output PMOS open-drain output port 3 for general purpose PMOS open-drain output port 2 to select the mid band PMOS open-drain output port 1 to select the low band bus voltage selection input ADC input or PMOS open-drain output port 5 for general purpose I2C-bus serial clock input I2C-bus serial data input and output I2C-bus address selection input crystal frequency buffer output crystal oscillator input 1 crystal oscillator input 2 not connected tuning voltage output charge pump output supply voltage for the PLL part PLL ground supply voltage for the analog part IF output B for symmetrical amplifier and asymmetrical IF amplifier switch input IF output A IF ground high band oscillator input 1 high band oscillator output 1 high band oscillator output 2 high band oscillator input 2
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Description
Product data sheet
Rev. 04 -- 8 December 2004
5 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
Pin description...continued Pin TDA6650TT TDA6651TT 5 4 3 2 1 mid band oscillator input 1 mid band oscillator input 2 oscillators ground low band oscillator output low band oscillator input 34 35 36 37 38 Description
Table 3: Symbol MOSCIN1 MOSCIN2 OSCGND LOSCOUT LOSCIN
6.2 Pinning
HBIN1 HBIN2 MBIN LBIN RFGND IFFIL1 IFFIL2 BS4 AGC
1 2 3 4 5 6 7 8 9
38 LOSCIN 37 LOSCOUT 36 OSCGND 35 MOSCIN2 34 MOSCIN1 33 HOSCIN2 32 HOSCOUT2 31 HOSCOUT1 30 HOSCIN1
LOSCIN LOSCOUT OSCGND MOSCIN2 MOSCIN1 HOSCIN2 HOSCOUT2 HOSCOUT1 HOSCIN1
1 2 3 4 5 6 7 8 9
38 HBIN1 37 HBIN2 36 MBIN 35 LBIN 34 RFGND 33 IFFIL1 32 IFFIL2 31 BS4 30 AGC
BS3 10 BS2 11 BS1 12 BVS 13 ADC/BS5 14 SCL 15 SDA 16 AS 17 XTOUT 18 XTAL1 19
TDA6650TT
29 IFGND 28 IFOUTA 27 IFOUTB 26 VCCA 25 PLLGND 24 VCCD 23 CP 22 VT 21 n.c. 20 XTAL2
001aac025
IFGND 10 IFOUTA 11 IFOUTB 12 VCCA 13 PLLGND 14 VCCD 15 CP 16 VT 17 n.c. 18 XTAL2 19
TDA6651TT
29 BS3 28 BS2 27 BS1 26 BVS 25 ADC/BS5 24 SCL 23 SDA 22 AS 21 XTOUT 20 XTAL1
001aac026
Fig 2. Pin configuration TDA6650TT
Fig 3. Pin configuration TDA6651TT
7. Functional description
7.1 Mixer, oscillator and PLL (MOPLL) functions
Bit BS1 enables the BS1 port, the low band mixer and the low band oscillator. Bit BS2 enables the BS2 port, the mid band mixer and the mid band oscillator. When both BS1 and BS2 bits are logic 0, the high band mixer and the high band oscillator are enabled. The oscillator signal is applied to the fractional-N programmable divider. The divided signal fdiv is fed to the phase comparator where it is compared in both phase and frequency with the comparison frequency fcomp. This frequency is derived from the signal present on the crystal oscillator fxtal and divided in the reference divider. There is a fractional calculator on the chip that generates the data for the fractional divider as well as
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
6 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
the reference divider ratio, depending on the step frequency selected. The crystal oscillator requires a 4 MHz crystal in series with an 18 pF capacitor between pins XTAL1 and XTAL2. The output of the phase comparator drives the charge pump and the loop amplifier section. This amplifier has an on-chip high voltage drive transistor. Pin CP is the output of the charge pump, and pin VT is the pin to drive the tuning voltage to the varicap diodes of the oscillators and the tracking filters. The loop filter has to be connected between pins CP and VT. The spurious signals introduced by the fractional divider are automatically compensated by the spurious compensation block. It is possible to drive the clock input of a digital demodulation IC from pin XTOUT with the 4 MHz signal from the crystal oscillator. This output is also used to output 12fdiv and fcomp signals in a specific test mode (see Table 8). It is possible to switch off this output, which is recommended when it is not used. For test and alignment purposes, it is also possible to release the tuning voltage output by selecting the sinking mode (see Table 8), and by applying an external voltage on pin VT. In addition to the BS1 and BS2 output ports that are used for the band selection, there are three general purpose ports BS3, BS4 and BS5. All five ports are PMOS open-drain type, each with 15 mA drive capability. The connection for port BS5 and the ADC input is combined on one pin. It is not possible to use the ADC if port BS5 is used. The AGC detector compares the level at the IF amplifier output to a reference level which is selected from 6 different levels via the I2C-bus. The time constant of the AGC can be selected via the I2C-bus to cope with normal operation as well as with search operation. When the output level on pin AGC is higher than the threshold VRMH, then bit AGC = 1. When the output level on pin AGC is lower than the threshold VRML, then bit AGC = 0. Between these two thresholds, bit AGC is not defined. The status of the AGC bit can be read via the I2C-bus according to the read mode as described in Table 14.
7.2 I2C-bus voltage
The I2C-bus lines SCL and SDA can be connected to an I2C-bus system tied to 2.5 V, 3.3 V or 5 V. The choice of the bus input threshold voltages is made with pin BVS that can be left open-circuit, connected to the supply voltage or to ground (see Table 4).
Table 4: I2C-bus voltage selection Bus voltage 2.5 V 3.3 V 5V Logic level LOW To ground Open-circuit To VCC 0 V to 0.75 V 0 V to 1.0 V 0 V to 1.5 V HIGH 1.75 V to 5.5 V 2.3 V to 5.5 V 3.0 V to 5.5 V
Pin BVS connection
7.3 Phase noise, I2C-bus traffic and crosstalk
While the TDA6650TT; TDA6651TT is dedicated for hybrid terrestrial applications, the low noise PLL will clean up the noise spectrum of the VCOs close to the carrier to reach noise levels at 1 kHz offset from the carrier compatible with e.g. DVB-T reception.
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
7 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
Linked to this noise improvement, some disturbances may become visible while they were not visible because they were hidden into the noise in analog dedicated applications and circuits. This is especially true for disturbances coming from the I2C-bus traffic, whatever this traffic is intended for the MOPLL or for another slave on the bus. To avoid this I2C-bus crosstalk and be able to have a clean noise spectrum, it is necessary to use a bus gate that enables the signal on the bus to drive the MOPLL only when the communication is intended for the tuner part (such a kind of I2C-bus gate is included into the Philips terrestrial channel decoders), and to avoid unnecessary repeated sending of the same information.
8. I2C-bus protocol
The TDA6650TT; TDA6651TT is controlled via the two-wire I2C-bus. For programming, there is one device address (7 bits) and the R/W bit for selecting read or write mode. To be able to have more than one MOPLL in an I2C-bus system, one of four possible addresses is selected depending on the voltage applied to address selection pin AS (see Table 7). The TDA6650TT; TDA6651TT fulfils the fast mode I2C-bus, according to the Philips I2C-bus specification (see Section 21), except for the timing as described in Figure 4. The I2C-bus interface is designed in such a way that the pins SCL and SDA can be connected to 5 V, 3.3 V or to 2.5 V pulled-up I2C-bus lines, depending on the voltage applied to pin BVS (see Table 4).
8.1 Write mode; R/W = 0
After the address transmission (first byte), data bytes can be sent to the device (see Table 5). Five data bytes are needed to fully program the TDA6650TT; TDA6651TT. The I2C-bus transceiver has an auto-increment facility that permits programming the device within one single transmission (address + 5 data bytes). The TDA6650TT; TDA6651TT can also be partly programmed on the condition that the first data byte following the address is byte 2 (divider byte 1) or byte 4 (control byte 1). The first bit of the first data byte transmitted indicates whether byte 2 (first bit = 0) or byte 4 (first bit = 1) will follow. Until an I2C-bus STOP condition is sent by the controller, additional data bytes can be entered without the need to re-address the device. The fractional calculator is updated only at the end of the transmission (STOP condition). Each control byte is loaded after the 8th clock pulse of the corresponding control byte. Main divider data are valid only if no new I2C-bus transmission is started (START condition) during the computation period of 50 s. Both DB1 and DB2 need to be sent to change the main divider ratio. If the value of the ratio selection bits R2, R1 and R0 are changed, the bytes DB1 and DB2 have to be sent in the same transmission.
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
8 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
50 s START ADDRESS DIVIDER BYTE BYTE 1 DIVIDER CONTROL CONTROL CONTROL CONTROL STOP BYTE 2 BYTE 1 BYTE 2 BYTE 1 BYTE 2 I2C-bus transmission dedicated to the MOPLL START ADDRESS BYTE
I2C-bus transmission dedicated to another IC
fce921
Fig 4. Example of I2C-bus transmission frame Table 5: Name Address byte Divider byte 1 (DB1) Divider byte 2 (DB2) Control byte 1 (CB1); see Table 6 Control byte 2 (CB2)
[1]
I2C-bus write data format Byte 1 2 3 4 5 Bit MSB [1] 1 0 N7 1 1 CP2 1 N14 N6 T/A = 1 T/A = 0 CP1 0 N13 N5 T2 0 CP0 0 N12 N4 T1 0 BS5 0 N11 N3 T0 ATC BS4 MA1 N10 N2 R2 AL2 BS3 MA0 N9 N1 R1 AL1 BS2 LSB R/W = 0 A N8 N0 R0 AL0 BS1 A A A A A Ack
MSB is transmitted first.
Table 6: Bit A
Description of write data format bits Description acknowledge programmable address bits; see Table 7 logic 0 for write mode programmable LO frequency; N = N14 x 214 + N13 x 213 + N12 x 212 + ... + N1 x 21 + N0 test/AGC bit T/A = 0: the next 6 bits sent are AGC settings T/A = 1: the next 6 bits sent are test and reference divider ratio settings
MA1 and MA0 R/W N14 to N0 T/A
T2, T1 and T0 R2, R1 and R0 ATC
test bits; see Table 8 reference divider ratio and programmable frequency step; see Table 9 AGC current setting and time constant; capacitor on pin AGC = 150 nF ATC = 0: AGC current = 220 nA; AGC time constant = 2 s ATC = 1: AGC current = 9 A; AGC time constant = 50 ms
AL2, AL1 and AL0 CP2, CP1 and CP0
AGC take-over point bits; see Table 10 charge pump current; see Table 11
BS5, BS4, BS3, BS2 PMOS ports control bits and BS1 BSn = 0: corresponding port is off, high-impedance state (status at power-on reset) BSn = 1: corresponding port is on; VO = VCC - VDS(sat)
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
9 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
8.1.1 I2C-bus address selection
The device address contains programmable address bits MA1 and MA0, which offer the possibility of having up to four MOPLL ICs in one system. Table 7 gives the relationship between the voltage applied to the AS input and the MA1 and MA0 bits.
Table 7: Address selection MA1 0 0 1 1 MA0 0 1 0 1
Voltage applied to pin AS 0 V to 0.1VCC 0.2VCC to 0.3VCC or open-circuit 0.4VCC to 0.6VCC 0.9VCC to VCC
8.1.2 XTOUT output buffer and mode setting
The crystal frequency can be sent to pin XTOUT and used in the application, for example to drive the clock input of a digital demodulator, saving a quartz crystal in the bill of material. To output fxtal, it is necessary to set T[2:0] to 001. If the output signal on this pin is not used, it is recommended to disable it, by setting T[2:0] to 000. This pin is also used to output 12fdiv and fcomp in a test mode. At power-on, the XTOUT output buffer is set to on, supplying the fxtal signal. The relation between the signal on pin XTOUT and the setting of theT[2:0] bits is given in Table 8.
Table 8: T2 0 0 0 0 1 1 1 1
[1]
XTOUT buffer status and test modes T1 0 0 1 1 0 0 1 1 T0 0 1 0 1 0 1 0 1 Pin XTOUT disabled fxtal (4 MHz)
1 f 2 div
Mode normal mode with XTOUT buffer off normal mode with XTOUT buffer on charge pump off switch ALBC on or off [1] test mode test mode charge pump sinking current [2] charge pump sourcing current
fxtal (4 MHz) fcomp
1 f 2 div
fxtal (4 MHz) disabled
Automatic Loop Bandwidth Control (ALBC) is disabled at power-on reset. After power-on reset this feature is enabled by setting T[2:0] = 011. To disable again the ALBC, set T[2:0] = 011 again. This test mode acts like a toggle switch, which means each time it is set the status of the ALBC changes. To toggle the ALBC, two consecutive Control byte 1s (CB1), should be sent: one byte with T[2:0] = 011 indicating that ALBC will be switched on or off and one byte programming the test mode to be selected (see Table 29, example of I2C-bus sequence). This is the default mode at power-on reset. This mode disables the tuning voltage.
[2]
8.1.3 Step frequency setting
The step frequency is set by three bits, giving five steps to cope with different application requirements. The reference divider ratio is automatically set depending on bits R2, R1 and R0. The phase detector works at either 4 MHz, 2 MHz or 1 MHz. Table 9 shows the step frequencies and corresponding reference divider ratios. When the value of bits R2, R1 and R0 are changed, it is necessary to re-send the data bytes DB1 and DB2.
9397 750 14178 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
10 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
Reference divider ratio select bits R1 0 0 1 1 0 0 1 1 R0 0 1 0 1 0 1 0 1 Reference divider Frequency ratio comparison 2 1 1 4 1 2 MHz 4 MHz 4 MHz 1 MHz 4 MHz Frequency step 62.5 kHz 142.86 kHz 166.67 kHz 50 kHz 125 kHz reserved reserved reserved
Table 9: R2 0 0 0 0 1 1 1 1
8.1.4 AGC detector setting
The AGC take-over point can be selected out of 6 levels according to Table 10.
Table 10: AL2 0 0 0 0 1 1 1 1
[1] [2] [3] [4]
AGC programming AL1 0 0 1 1 0 0 1 1 AL0 0 1 0 1 0 1 0 1
[1] [1] [1] [2] [2] [2] [3] [4]
Typical take-over point level 124 dBV (p-p) 121 dBV (p-p) 118 dBV (p-p) 115 dBV (p-p) 112 dBV (p-p) 109 dBV (p-p) IAGC = 0 A VAGC = 3.5 V
This take-over point is available for both symmetrical and asymmetrical modes. This take-over point is available for asymmetrical mode only. The AGC current sources are disabled. The AGC output goes into a high-impedance state and an external AGC source can be connected in parallel and will not be influenced. The AGC detector is disabled and IAGC = 9 A.
8.1.5 Charge pump current setting
The charge pump current can be chosen from 8 values depending on the value of bits CP2, CP1 and CP0 bits; see Table 11. The programming of the CP bits are not taken into account when ALBC mode is in use.
Table 11: CP2 0 0 0 0 1 Charge pump current CP1 0 0 1 1 0 CP0 0 1 0 1 0 Charge pump current number 1 2 3 4 5 Typical current (absolute value in A) 38 54 83 122 163
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
11 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
Charge pump current...continued CP1 0 1 1 CP0 1 0 1 Charge pump current number 6 7 8 Typical current (absolute value in A) 254 400 580
Table 11: CP2 1 1 1
8.1.6 Automatic Loop Bandwidth Control (ALBC)
In a PLL controlled VCO in which the PLL reduces phase noise close to the carrier, there is an optimum loop bandwidth corresponding to the minimum integrated phase jitter. This loop bandwidth depends on different parameters like the VCO slope, the loop filter components, the dividing ratio and the gain of the phase detector and charge pump. In order to reach the best phase noise performance it is necessary, especially in a wideband system like a digital tuner, to set the charge pump current to different values depending on the band and frequency used. This is to cope with the variations of the different parameters that set the bandwidth. The selection can be done in the application and requires for each frequency to program not only the divider ratios, but also the band and the best charge pump current. The TDA6650TT; TDA6651TT includes the ALBC feature that automatically sets the band and the charge pump current, provided the IC is used in the DVB-T standard application shown in Figure 27 and 28. This feature is activated by setting bits T[2:0] = 011 after power-on reset. This feature is disabled when the same bits are set again. When ALBC is activated, the output ports BS1, BS2 and BS3 are not programmed by the corresponding BS bits, but are set according to Table 12 and 13. When ALBC is active, bit ALBC = 1. Table 13 summarizes the programming of the band selection and the charge pump current when ALBC is active.
Table 12: Bit ALBC 0 0 0 0 1 Table 13: BS3 X X X X X BS2 0 0 1 1 X BS1 0 1 0 1 X ALBC settings Band selected high low mid forbidden depends on LO program, shown in Table 13 Charge pump Port current BS3 see Table 13 see Table 13 see Table 13 follows bit BS3 follows bit BS3 follows bit BS3 BS2 off off on BS1 off on off
ALBC band selection and charge current setting Band low low low low low Charge pump current number 2 3 4 5 6
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
LO frequency 80 MHz to 92 MHz 92 MHz to 144 MHz 144 MHz to 156 MHz 156 MHz to 176 MHz 176 MHz to 184 MHz
9397 750 14178
Product data sheet
Rev. 04 -- 8 December 2004
12 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
ALBC band selection and charge current setting...continued Band low mid mid mid mid mid mid mid high high high high high Charge pump current number 7 2 3 4 5 6 7 8 4 5 6 7 8
Table 13:
LO frequency 184 MHz to 196 MHz 196 MHz to 224 MHz 224 MHz to 296 MHz 296 MHz to 380 MHz 380 MHz to 404 MHz 404 MHz to 448 MHz 448 MHz to 472 MHz 472 MHz to 484 MHz 484 MHz to 604 MHz 604 MHz to 676 MHz 676 MHz to 752 MHz 752 MHz to 868 MHz 868 MHz to 904 MHz
8.2 Read mode; R/W = 1
Data can be read from the device by setting the R/W bit to 1 (see Table 14). After the device address has been recognized, the device generates an acknowledge pulse and the first data byte (status byte) is transferred on the SDA line (MSB first). Data is valid on the SDA line during a HIGH level of the SCL clock signal. A second data byte can be read from the device if the microcontroller generates an acknowledge on the SDA line (master acknowledge). End of transmission will occur if no master acknowledge occurs. The device will then release the data line to allow the microcontroller to generate a STOP condition.
Table 14: Name I2C-bus read data format Byte Bit MSB [1] Address byte 1 Status byte
[1]
ACK LSB 1 FL 0 ALBC 0 1 0 AGC MA1 A2 MA0 A1 R/W = 1 A A0 -
1 POR
2
MSB is transmitted first.
Table 15: Bit A POR
Description of read data format bits Description acknowledge bit power-on reset flag POR = 0, normal operation POR = 1, power-on reset
FL
in-lock flag FL = 0, not locked FL = 1, the PLL is locked
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
13 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
Description of read data format bits...continued Description automatic loop bandwidth control flag ALBC = 0, no automatic loop bandwidth control ALBC = 1, automatic loop bandwidth control selected
Table 15: Bit ALBC
AGC
internal AGC flag AGC = 0 when internal AGC is active (VAGC < VRML) AGC = 1 when internal AGC is not active (VAGC > VRMH)
A2, A1, A0 Table 16:
digital outputs of the 5-level ADC; see Table 16 ADC levels A2 1 0 0 0 0 A1 0 1 1 0 0 A0 0 1 0 1 0
Voltage applied to pin ADC [1] 0.6VCC to VCC 0.45VCC to 0.6VCC 0.3VCC to 0.45VCC 0.15VCC to 0.3VCC 0 V to 0.15VCC
[1]
Accuracy is 0.03VCC. Bit BS5 must be set to logic 0 to disable the BS5 output port. The BS5 output port uses the same pin as the ADC and can not be used when the ADC is in use.
8.3 Status at power-on reset
At power on or when the supply voltage drops below approximately 2.85 V (at Tamb = 25 C), internal registers are set according to Table 17. At power on, the charge pump current is set to 580 A, the test bits T[2:0] are set to 110 which means that the charge pump is sinking current, the tuning voltage output is disabled and the ALBC function is disabled. The XTOUT buffer is on, driving the 4 MHz signal from the crystal oscillator and all the ports are off. As a consequence, the high band is selected by default.
Table 17: Name Address byte Divider byte 1 (DB1) Divider byte 2 (DB2) Control byte 1 (CB1) Control byte 2 (CB2)
[1] [2] [3]
Default setting at power-on reset Byte 1 2 3 4 5 Bit [1] MSB 1 0 N7 = X 1 1 CP2 = 1 1 N14 = X N6 = X T/A = T/A = X [2] X [3] 0 N13 = X N5 = X T2 = 1 0 CP0 = 1 0 N12 = X N4 = X T1 = 1 0 BS5 = 0 0 N11 = X N3 = X T0 = 0 ATC = 0 BS4 = 0 MA1 N10 = X N2 = X R2 = X AL2 = 0 BS3 = 0 MA0 N9 = X N1 = X R1 = X AL1 = 1 BS2 = 0 LSB X N8 = X N0 = X R0 = X AL0 = 0 BS1 = 0
CP1 = 1
X means that this bit is not set or reset at power-on reset. The next six bits are written, when bit T/A = 1 in a write sequence. The next six bits are written, when bit T/A = 0 in a write sequence.
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
14 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
9. Internal circuitry
Table 18: Symbol Internal pin configuration Pin TDA6650TT HBIN1 HBIN2 1 2 TDA6651TT 38 37 Average DC voltage versus band selection Low n.a. n.a. Mid n.a n.a High 1.0 V 1.0 V
(38) 1 2 (37)
Description [1]
fce899
MBIN
3
36
n.a.
1.8 V
n.a.
(36) 3
fce901
LBIN
4
35
1.8 V
n.a.
n.a
(35) 4
fce898
RFGND
5
34
-
-
5 (34)
fce897
IFFIL1 IFFIL2
6 7
33 32
3.7 V 3.7 V
3.7 V 3.7 V
3.7 V 3.7 V
(33) 6 7 (32)
fce896
BS4
8
31
high-Z or high-Z or high-Z or VCC - VDS VCC - VDS VCC - VDS
8 (31)
fce895
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
15 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
Table 18: Symbol
Internal pin configuration...continued Pin TDA6650TT TDA6651TT 30 Average DC voltage versus band selection Low 0 V or 3.5 V Mid 0 V or 3.5 V High 0 V or 3.5 V
9 (30)
Description [1]
AGC
9
fce907
BS3
10
29
high-Z or high-Z or high-Z or VCC - VDS VCC - VDS VCC - VDS
10 (29)
fce893
BS2
11
28
high-Z
VCC - VDS high-Z
11 (28)
fce892
BS1
12
27
VCC - VDS high-Z
high-Z
12 (27)
fce891
BVS
13
26
2.5 V
2.5 V
2.5 V
(26) 13
mce163
ADC/BS5
14
25
VCEsat or high-Z
VCEsat or high-Z
VCEsat or high-Z
(25) 14
fce887
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
16 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
Table 18: Symbol
Internal pin configuration...continued Pin TDA6650TT TDA6651TT 24 Average DC voltage versus band selection Low high-Z Mid high-Z High high-Z Description [1]
SCL
15
(24) 15
fce889
SDA
16
23
high-Z
high-Z
high-Z
(23) 16
fce888
AS
17
22
1.25 V
1.25 V
1.25 V
(22) 17
fce890
XTOUT
18
21
3.45 V
3.45 V
3.45 V
18 (21)
mce164
XTAL1 XTAL2
19 20
20 19
2.2 V 2.2 V
2.2 V 2.2 V
2.2 V 2.2 V
19 (20)
20 (19)
fce883
n.c.
21
18
n.a.
not connected
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
17 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
Table 18: Symbol
Internal pin configuration...continued Pin TDA6650TT TDA6651TT 17 Average DC voltage versus band selection Low VVT Mid VVT High VVT
22 (17)
Description [1]
VT
22
fce884
CP
23
16
1.8 V
1.8 V
1.8 V
23 (16)
fce885
VCCD PLLGND
24 25
15 14
5V -
5V -
5V 25 (14)
fce882
VCCA IFOUTB IFOUTA
26 27 28
13 12 11
5V 2.1 V 2.1 V
5V 2.1 V 2.1 V
5V 2.1 V 2.1 V
28 (11)
fce886
IFGND
29
10
-
-
29 (10)
fce880
HOSCIN1 HOSCOUT1 HOSCOUT2 HOSCIN2
30 31 32 33
9 8 7 6
2.2 V 5V 5V 2.2 V
2.2 V 5V 5V 2.2 V
1.8 V 2.5 V 2.5 V 1.8 V
(8) 31 (6) 33 32 (7) 30 (9)
fce879
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
18 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
Table 18: Symbol
Internal pin configuration...continued Pin TDA6650TT TDA6651TT 5 4 Average DC voltage versus band selection Low 2.3 V 2.3 V Mid 1.3 V 1.3 V High 2.3 V 2.3 V Description [1]
MOSCIN1 MOSCIN2
34 35
34 (5)
35 (4)
fce878
OSCGND
36
3
-
-
36 (3)
fce908
LOSCOUT LOSCIN
37 38
2 1
1.7 V 2.9 V
1.4 V 3.5 V
1.4 V 3.5 V
37 (2) (1) 38
fce877
[1]
The pin numbers in parenthesis refer to the TDA6651TT.
10. Limiting values
Table 19: Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Positive currents are entering the IC and negative currents are going out of the IC; all voltages are referenced to ground (GND) [1]. Symbol VCCA, VCCD VVT VSDA ISDA VSCL VAS Parameter supply voltage tuning voltage output serial data input and output voltage serial data output current serial clock input voltage address selection input voltage during acknowledge Conditions Min -0.3 -0.3 -0.3 0 -0.3 -0.3 Max +6 +35 +6 10 +6 +6 Unit V V V mA V V
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
19 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
Table 19: Limiting values...continued In accordance with the Absolute Maximum Rating System (IEC 60134). Positive currents are entering the IC and negative currents are going out of the IC; all voltages are referenced to ground (GND) [1]. Symbol Vn Parameter voltage on all other inputs, outputs and combined inputs and outputs, except GNDs PMOS port output current Conditions 4.5 V < VCC < 5.5 V Min -0.3 Max VCC + 0.3 Unit V
IBSn IBS(tot) tsc(max) Tstg Tamb Tj
[1] [2]
corresponding port on; open-drain
-20 -50 -40
[2]
0 0 10 +150 Tamb(max) 150
mA mA s C C C
sum of all PMOS port output open-drain currents maximum short-circuit time storage temperature ambient temperature junction temperature each pin to VCC or to GND
-20 -
Maximum ratings cannot be exceeded, not even momentarily without causing irreversible IC damage. Maximum ratings cannot be accumulated. The maximum allowed ambient temperature Tamb(max) depends on the assembly conditions of the package and especially on the design of the printed-circuit board. The application mounting must be done in such a way that the maximum junction temperature is never exceeded. An estimation of the junction temperature can be obtained through measurement of the temperature of the top center of the package (Tpackage). The temperature difference junction to case (Tj-c) is estimated at about 13 C on the demo board (PCB 827-3). The junction temperature: Tj = Tpackage + Tj-c.
11. Thermal characteristics
Table 20: Symbol Rth(j-a) Thermal characteristics Parameter thermal resistance from junction to ambient TDA6650TT TDA6651TT
[1] [2] Measured in free air as defined by JEDEC standard JESD51-2. These values are given for information only. The thermal resistance depends strongly on the nature and design of the printed-circuit board used in the application.The thermal resistance given corresponds to the value that can be measured on a multilayer printed-circuit board (4 layers) as defined by JEDEC standard. The junction temperature influences strongly the reliability of an IC. The printed-circuit board used in the application contributes in a large part to the overall thermal characteristic. It must therefore be insured that the junction temperature of the IC never exceeds Tj(max) = 150 C at the maximum ambient temperature.
Conditions
[1] [2] [3]
Typ
Unit
82 74
K/W K/W
[3]
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
20 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
12. Characteristics
Table 21: Characteristics VCCA = VCCD = 5 V, Tamb = 25 C; values are given for an asymmetrical IF output loaded with a 75 load or with a symmetrical IF output loaded with 1.25 k; positive currents are entering the IC and negative currents are going out of the IC; the performances of the circuits are measured in the measurement circuits Figure 27 and 28 for digital application or in the measurement circuits Figure 29 and 30 for hybrid application; unless otherwise specified. Symbol Supply VCC ICC supply voltage supply current PMOS ports off one PMOS port on: sourcing 15 mA two PMOS ports on: one port sourcing 15 mA and one other port sourcing 5 mA General functions VPOR flock power-on reset supply voltage frequency range the PLL is able to synthesize crystal frequency input impedance (absolute value) crystal drive level output leakage current in off state output saturation voltage fxtal = 4 MHz; VCC = 4.5 V to 5.5 V; Tamb = -20 C to + Tamb(max), see Section 10 fxtal = 4 MHz VCC = 5.5 V; VBS = 0 V only corresponding buffer is on, sourcing 15 mA; VDS(sat) = VCC - VBS see Table 16 VADC = VCC VADC = 0 V VAS = 5.5 V VAS = 0 V VBVS = 5.5 V VBVS = 0 V
[3] [2]
Parameter
Conditions
Min 4.5 80 96 101
Typ 5.0 96 112 117
Max 5.5 115 131 136
Unit V mA mA mA
power-on reset active if VCC < VPOR
64
2.85 -
3.5 1024
V MHz
Crystal oscillator [1] fxtal Zxtal 350 4.0 430 MHz
Pxtal ILO(off) VDS(sat)
-10 -
70 0.2
0.4
W A V
PMOS ports: pins BS1, BS2, BS3, BS4 and BS5
ADC input: pin ADC Vi IIH IIL IIH IIL IIH IIL Vo(p-p) ADC input voltage HIGH-level input current LOW-level input current HIGH-level input current LOW-level input current HIGH-level input current LOW-level input current square wave AC output voltage (peak-to peak value) output impedance 0 -10 -10 -100 400 5.5 10 10 100 V A A A A A A mV
Address selection input: pin AS
Bus voltage selection input: pin BVS
Buffered output: pin XTOUT
Zo
-
175
-
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
21 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
Table 21: Characteristics...continued VCCA = VCCD = 5 V, Tamb = 25 C; values are given for an asymmetrical IF output loaded with a 75 load or with a symmetrical IF output loaded with 1.25 k; positive currents are entering the IC and negative currents are going out of the IC; the performances of the circuits are measured in the measurement circuits Figure 27 and 28 for digital application or in the measurement circuits Figure 29 and 30 for hybrid application; unless otherwise specified. Symbol I2C-bus Inputs: pins SCL and SDA fclk VIL clock frequency LOW-level input voltage frequency on SCL VBVS = 0 V VBVS = 2.5 V or open-circuit VBVS = 5 V VIH HIGH-level input voltage VBVS = 0 V VBVS = 2.5 V or open-circuit VBVS = 5 V IIH IIL HIGH-level input current LOW-level input current VCC = 0 V; VBUS = 5.5 V VCC = 5.5 V; VBUS = 5.5 V VCC = 0 V; VBUS = 1.5 V VCC = 5.5 V; VBUS = 0 V Output: pin SDA ILH VO(ack) leakage current output voltage during acknowledge output current (absolute value) off-state leakage current leakage current when switched-off output voltage when the loop is closed phase jitter (RMS value) VSDA = 5.5 V ISDA = 3 mA 10 0.4 A V 0 0 0 1.75 2.3 3.0 -10 400 0.75 1.0 1.5 5.5 5.5 5.5 10 10 10 kHz V V V V V V A A A A Parameter Conditions Min Typ Max Unit
Charge pump output: pin CP Io IL(off) IL(off) Vo(cl) see Table 11 charge pump off (T[2:0] = 010) tuning supply voltage = 33 V tuning supply voltage = 33 V; RL = 15 k integrated between 1 kHz and 1 MHz offset from the carrier digital application hybrid application Low band mixer, including IF amplifier fRF RF frequency picture carrier
[4]
-15 0.3
0 -
+15 10 32.7
A nA A V
Tuning voltage output: pin VT
Noise performance J(rms)
43.25
0.5 0.6 -
-
deg deg
157.25 MHz
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
22 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
Table 21: Characteristics...continued VCCA = VCCD = 5 V, Tamb = 25 C; values are given for an asymmetrical IF output loaded with a 75 load or with a symmetrical IF output loaded with 1.25 k; positive currents are entering the IC and negative currents are going out of the IC; the performances of the circuits are measured in the measurement circuits Figure 27 and 28 for digital application or in the measurement circuits Figure 29 and 30 for hybrid application; unless otherwise specified. Symbol Gv Parameter voltage gain Conditions asymmetrical IF output; RL = 75 ; see Figure 14 fRF = 44.25 MHz fRF = 157.25 MHz symmetrical IF output; RL = 1.25 k; see Figure 15 fRF = 44.25 MHz fRF = 157.25 MHz NF noise figure see Figure 16 and 17 fRF = 50 MHz fRF = 150 MHz Vo output voltage causing 1 % cross modulation in channel asymmetrical application; see Figure 18 fRF = 44.25 MHz fRF = 157.25 MHz symmetrical application; see Figure 19 fRF = 44.25 MHz fRF = 157.25 MHz Vi input voltage causing 750 Hz frequency deviation pulling in channel channel SO2 beat input level without lock-out input conductance input capacitance asymmetrical IF output
[5] [5]
Min
Typ
Max
Unit
21 21
24 24
27 27
dB dB
25 25 -
28 28 8.0 8.0
31 31 10.0 10.0
dB dB dB dB
107 107 117 117 -
110 110 120 120 90
-
dBV dBV dBV dBV dBV
INTSO2 Vi(lock) Gi Ci
VRFpix = 80 dBV see Figure 25 fRF = 44.25 MHz; see Figure 5 fRF = 157.25 MHz; see Figure 5 fRF = 44.25 MHz to 157.25 MHz; see Figure 5 picture carrier asymmetrical IF output; load = 75 ; see Figure 14 fRF = 157.25 MHz fRF = 443.25 MHz symmetrical IF output; load = 1.25 k; see Figure 15 fRF = 157.25 MHz fRF = 443.25 MHz
[6] [7]
57 -
60 0.13 0.11 1.36
120 -
dBc dBV mS mS pF
Mid band mixer, including IF amplifier fRF Gv RF frequency voltage gain
[4]
157.25 -
443.25 MHz
21 21
24 24
27 27
dB dB
25 25
28 28
31 31
dB dB
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
23 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
Table 21: Characteristics...continued VCCA = VCCD = 5 V, Tamb = 25 C; values are given for an asymmetrical IF output loaded with a 75 load or with a symmetrical IF output loaded with 1.25 k; positive currents are entering the IC and negative currents are going out of the IC; the performances of the circuits are measured in the measurement circuits Figure 27 and 28 for digital application or in the measurement circuits Figure 29 and 30 for hybrid application; unless otherwise specified. Symbol NF Parameter noise figure Conditions see Figure 16 and 17 fRF = 150 MHz fRF = 300 MHz Vo output voltage causing 1 % cross modulation in channel asymmetrical application; see Figure 18 fRF = 157.25 MHz fRF = 443.25 MHz symmetrical application; see Figure 19 fRF = 157.25 MHz fRF = 443.25 MHz Vf(N+5)-1 (N + 5) - 1 MHz pulling fRF(wanted) = 443.25 MHz; fosc = 482.15 MHz; fRF(unwanted) = 482.25 MHz asymmetrical IF output
[8] [5] [5]
Min -
Typ 8.0 9.0
Max 10.0 11.0
Unit dB dB
107 107 117 117 -
110 110 120 120 80
-
dBV dBV dBV dBV dBV
Vi
input voltage causing 750 Hz frequency deviation pulling in channel input level without lock-out input conductance input capacitance RF frequency voltage gain
-
89
-
dBV
Vi(lock) Gi Ci fRF Gv
see Figure 25 see Figure 6 see Figure 6 picture carrier asymmetrical IF output; load = 75 ; see Figure 20 fRF = 443.25 MHz fRF = 863.25 MHz symmetrical IF output; load = 1.25 k; see Figure 21 fRF = 443.25 MHz fRF = 863.25 MHz
[7]
-
0.3 1.1
120 -
dBV mS pF
High band mixer, including IF amplifier
[4]
443.25 -
863.25 MHz
31.5 31.5
34.5 34.5
37.5 37.5
dB dB
35.5 35.5 [5]
38.5 38.5 6.0 7.0
41.5 41.5 8.0 9.0
dB dB dB dB
NF
noise figure, not corrected see Figure 22 for image fRF = 443.25 MHz fRF = 863.25 MHz output voltage causing 1 % cross modulation in channel asymmetrical application; see Figure 23 fRF = 443.25 MHz fRF = 863.25 MHz symmetrical application; see Figure 24 fRF = 443.25 MHz fRF = 863.25 MHz
[5]
Vo
107 107 117 117
110 110 120 120
-
dBV dBV dBV dBV
24 of 54
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
Table 21: Characteristics...continued VCCA = VCCD = 5 V, Tamb = 25 C; values are given for an asymmetrical IF output loaded with a 75 load or with a symmetrical IF output loaded with 1.25 k; positive currents are entering the IC and negative currents are going out of the IC; the performances of the circuits are measured in the measurement circuits Figure 27 and 28 for digital application or in the measurement circuits Figure 29 and 30 for hybrid application; unless otherwise specified. Symbol Vi(lock) Vf(N+5)-1 Vi Parameter input level without lock-out (N + 5) - 1 MHz pulling input voltage causing 750 Hz frequency deviation pulling in channel input impedance (RS + jLS) Conditions see Figure 26 fRF(wanted) = 815.25 MHz; fosc = 854.15 MHz; fRF(unwanted) = 854.25 MHz asymmetrical IF output
[7]
Min -
Typ 80 79
Max 120 -
Unit dBV dBV dBV
[8]
Zi
fRF = 443.25 MHz; see Figure 7 RS LS fRF = 863.25 MHz; see Figure 7 RS LS [9] [10]
-
35 8 36 8 110 900 95
-
nH nH
Low band oscillator fosc fosc(V) fosc(T) osc(dig) oscillator frequency oscillator frequency shift with supply voltage oscillator frequency drift with temperature phase noise, carrier to sideband noise in digital application T = 25 C; VCC = 5 V with compensation 1 kHz frequency offset; fcomp = 4 MHz; see Figure 8, 27 and 28 10 kHz frequency offset; worst case in the frequency range; see Figure 9, 27 and 28 100 kHz frequency offset; worst case in the frequency range; see Figure 10, 27 and 28 1.4 MHz frequency offset; worst case in the frequency range; see Figure 27 and 28 osc(hyb) phase noise, carrier to sideband noise in hybrid application 1 kHz frequency offset; fcomp = 4 MHz; see Figure 11, 29, and 30 10 kHz frequency offset; worst case in the frequency range; see Figure 12, 29, and 30 100 kHz frequency offset; worst case in the frequency range; see Figure 13, 29, and 30 1.4 MHz frequency offset; worst case in the frequency range; see Figure 29 and 30
9397 750 14178
83.15 82
196.15 MHz kHz kHz dBc/Hz
[11]
87
100
-
dBc/Hz
104
110
-
dBc/Hz
-
117
-
dBc/Hz
80
95
-
dBc/Hz
85
96
-
dBc/Hz
104
110
-
dBc/Hz
-
117
-
dBc/Hz
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
25 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
Table 21: Characteristics...continued VCCA = VCCD = 5 V, Tamb = 25 C; values are given for an asymmetrical IF output loaded with a 75 load or with a symmetrical IF output loaded with 1.25 k; positive currents are entering the IC and negative currents are going out of the IC; the performances of the circuits are measured in the measurement circuits Figure 27 and 28 for digital application or in the measurement circuits Figure 29 and 30 for hybrid application; unless otherwise specified. Symbol RSCp-p Parameter Conditions
[12]
Min 15
Typ 200
Max -
Unit mV
ripple susceptibility of VCC VCC = 5 V 5 %; worst case in the frequency range; ripple frequency (peak-to-peak value) 500 kHz oscillator frequency oscillator frequency shift with supply voltage oscillator frequency drift with temperature phase noise, carrier to sideband noise in digital application T = 25 C; VCC = 5 V with compensation 1 kHz frequency offset; fcomp = 4 MHz; see Figure 8, 27 and 28 10 kHz frequency offset; worst case in the frequency range; see Figure 9, 27 and 28 100 kHz frequency offset; worst case in the frequency range; see Figure 10, 27 and 28 1.4 MHz frequency offset; worst case in the frequency range; see Figure 27 and 28
Mid band oscillator fosc fosc(V) fosc(T) osc(dig)
[9] [10]
196.15 85 110 1500 90
482.15 MHz kHz kHz dBc/Hz
[11]
87
95
-
dBc/Hz
104
110
-
dBc/Hz
-
115
-
dBc/Hz
osc(hyb)
phase noise, carrier to sideband noise in hybrid application
1 kHz frequency offset; fcomp = 4 MHz; see Figure 11, 29 and 30 10 kHz frequency offset; worst case in the frequency range; see Figure 12, 29 and 30 100 kHz frequency offset; worst case in the frequency range; see Figure 13, 29 and 30 1.4 MHz frequency offset; worst case in the frequency range; see Figure 29 and 30
82
88
-
dBc/Hz
85
90
-
dBc/Hz
104
110
-
dBc/Hz
-
115
-
dBc/Hz
RSCp-p
ripple susceptibility of VCC VCC = 5 V 5 %; worst case in the frequency range; ripple frequency (peak-to-peak value) 500 kHz oscillator frequency oscillator frequency shift with supply voltage oscillator frequency drift with temperature T = 25 C; VCC = 5 V; with compensation
[12]
15
140
-
mV
High band oscillator fosc fosc(V) fosc(T)
[9] [10]
482.15 300 1100
902.15 MHz kHz kHz
[11]
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
26 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
Table 21: Characteristics...continued VCCA = VCCD = 5 V, Tamb = 25 C; values are given for an asymmetrical IF output loaded with a 75 load or with a symmetrical IF output loaded with 1.25 k; positive currents are entering the IC and negative currents are going out of the IC; the performances of the circuits are measured in the measurement circuits Figure 27 and 28 for digital application or in the measurement circuits Figure 29 and 30 for hybrid application; unless otherwise specified. Symbol osc(dig) Parameter phase noise, carrier to sideband noise in digital application Conditions 1 kHz frequency offset; fcomp = 4 MHz; see Figure 8, 27 and 28 10 kHz frequency offset; worst case in the frequency range; see Figure 9, 27 and 28 100 kHz frequency offset; worst case in the frequency range; see Figure 11, 27 and 28 1.4 MHz frequency offset; worst case in the frequency range; see Figure 27 and 28 osc(hyb) phase noise, carrier to sideband noise in hybrid application 1 kHz frequency offset; fcomp = 4 MHz; see Figure 11, 29 and 30 10 kHz frequency offset; worst case in the frequency range; see Figure 12, 29 and 30 100 kHz frequency offset; worst case in the frequency range; see Figure 13, 29 and 30 1.4 MHz frequency offset; worst case in the frequency range; see Figure 29 and 30 RSCp-p ripple susceptibility of VCC VCC = 5 V 5 %; worst case in the frequency range; ripple frequency (peak-to-peak value) 500 kHz output impedance asymmetrical IF output RS at 38.9 MHz LS at 38.9 MHz symmetrical IF output RS at 38.9 MHz LS at 38.9 MHz Rejection at the IF output (IF amplifier in asymmetrical mode) INTdiv INTxtal divider interferences in IF level crystal oscillator interferences rejection worst case VIF = 100 dBV; worst case in the frequency range
[13] [12]
Min 85
Typ 89
Max -
Unit dBc/Hz
87
93
-
dBc/Hz
104
107
-
dBc/Hz
-
117
-
dBc/Hz
80
85
-
dBc/Hz
82
86
-
dBc/Hz
104
107
-
dBc/Hz
-
117
-
dBc/Hz
15
40
-
mV
IF amplifier Zo 100 10.4 50 5.4 20 -50 nH dBV dBc nH
[14]
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
27 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
Table 21: Characteristics...continued VCCA = VCCD = 5 V, Tamb = 25 C; values are given for an asymmetrical IF output loaded with a 75 load or with a symmetrical IF output loaded with 1.25 k; positive currents are entering the IC and negative currents are going out of the IC; the performances of the circuits are measured in the measurement circuits Figure 27 and 28 for digital application or in the measurement circuits Figure 29 and 30 for hybrid application; unless otherwise specified. Symbol INTf(step) Parameter step frequency rejection Conditions measured in digital application for DVB-T; fstep = 166.67 kHz; IF = 36.125 MHz measured in hybrid application for DVB-T; fstep = 166.67 kHz; IF = 36.125 MHz measured in hybrid application for PAL; fstep = 62.5 kHz; IF = 38.9 MHz measured in hybrid application for FM; fstep = 50 kHz; IF = 38.9 MHz INTXTH crystal oscillator harmonics in the IF frequency bits AL[2:0] = 000
[15]
Min -
Typ -
Max -50
Unit dBc
[15]
-
-
-57
dBc
[15]
-
-
-57 -57 45
dBc dBc dBV
[15]
[16]
AGC output (IF amplifier in asymmetrical mode): pin AGC AGCTOP(p-p) AGC take-over point (peak-to-peak level) Isource(fast) Isource(slow) Vo Vo(dis) VRF(slip) source current fast source current slow output voltage output voltage with AGC disabled RF voltage range to switch the AGC from active to not active mode low threshold AGC output AGC bit = 0 or AGC not active voltage high threshold AGC output voltage leakage current AGC bit = 1 or AGC active bits AL[2:0] = 110; 0 < VAGC < VCC maximum level minimum level bits AL[2:0] = 111 122.5 7.5 185 3.45 0 3.45 124 9.0 220 3.55 3.55 125.5 11.6 280 3.8 0.1 3.8 0.5 dBV A nA V V V dB
VRML VRMH ILO
[1]
0 3.2 -50
3.55 -
2.8 3.8 +50
V V nA
Important recommendation: to obtain the performances mentioned in this specification, the serial resistance of the crystal used with this oscillator must never exceed 120 . The crystal oscillator is guaranteed to operate at any supply voltage between 4.5 V and 5.5 V and at any temperature between -20 C and Tamb(max), as defined in Section 10. The drive level is expected with a 50 series resistance of the crystal at series resonance. The drive level will be different with other series resistance values. The VXTOUT level is measured when the pin XTOUT is loaded with 5 k in parallel with 10 pF. The RF frequency range is defined by the oscillator frequency range and the intermediate frequency (IF). The 1 % cross modulation performance is measured with AGC detector turned off (AGC bits set to 110). Channel SO2 beat is the interfering product of fRFpix, fIF and fosc of channel SO2; fbeat = 37.35 MHz. The possible mechanisms are: fosc - 2 x fIFpix or 2 x fRFpix - fosc. The IF output signal stays stable within the range of the step frequency for any RF input level up to 120 dBV. (N + 5) - 1 MHz pulling is the input level of channel N + 5, at frequency 1 MHz lower, causing 100 kHz FM sidebands 30 dB below the wanted carrier.
[2] [3] [4] [5] [6] [7] [8]
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
28 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
[9]
Limits are related to the tank circuits used in Figure 27 and 28 for digital application or Figure 29 and 30 for hybrid application. Frequency bands may be adjusted by the choice of external components.
[10] The frequency shift is defined as a change in oscillator frequency when the supply voltage varies from VCC = 5 V to 4.5 V or from VCC = 5 V to 5.25 V. The oscillator is free running during this measurement. [11] The frequency drift is defined as a change in oscillator frequency when the ambient temperature varies from Tamb = 25 C to 50 C or from Tamb = 25 C to 0 C. The oscillator is free running during this measurement. [12] The supply ripple susceptibility is measured in the measurement circuit according to Figure 27, 28, 29 and 30 using a spectrum analyzer connected to the IF output. An unmodulated RF signal is applied to the test board RF input. A sinewave signal with a frequency of 500 kHz is superimposed onto the supply voltage. The amplitude of this ripple signal is adjusted to bring the 500 kHz sidebands around the IF carrier to a level of -53.5 dB with respect to the carrier. [13] This is the level of divider interferences close to the IF frequency. For example channel S3: fosc = 158.15 MHz, 14 fosc = 39.5375 MHz. The low and mid band inputs must be left open (i.e. not connected to any load or cable); the high band inputs are connected to an hybrid. [14] Crystal oscillator interference means the 4 MHz sidebands caused by the crystal oscillator. [15] The step frequency rejection is the level of step frequency sidebands (e.g. 166.67 kHz) related to the carrier. [16] This is the level of the 9th and 11th harmonics of the 4 MHz crystal oscillator into the IF output.
1 2 0.5
5 10
0.2
10 5
-j 10 5 2 1 0.5 0.2 40 MHz 200 MHz 0.2 0 +j
2 1
0.5
mce160
Fig 5. Input admittance (s11) of the low band mixer (40 MHz to 200 MHz); Yo = 20 mS
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
29 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
1 2 0.5
5 10
0.2
10 5
-j 10 5 2 1 0.5 0.2 100 MHz 0 +j
500 MHz
0.2
2 1
0.5
mce161
Fig 6. Input admittance (s11) of the mid band mixer (100 MHz to 500 MHz); Yo = 20 mS
1 0.5 2
900 MHz 0.2 400 MHz +j 0 -j 10 0.2 5 0.2 0.5 1 2 5 10 5 10
0.5 1
2
mce165
Fig 7. Input impedance (s11) of the high band mixer (400 MHz to 900 MHz); Zo = 100
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
30 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
-80
fce915
osc
(dBc/Hz) -85
-90
-95
-100
40
140
240
340
440
540
640
740
840 fRF (MHz)
940
Fig 8. 1 kHz phase noise typical performance in digital application (Figure 27 and 28)
osc
-80
fce916
(dBc/Hz) -85
-90
-95
-100
-105
-110
40
140
240
340
440
540
640
740
840 fRF (MHz)
940
Fig 9. 10 kHz phase noise typical performance in digital application (Figure 27 and 28)
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
31 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
-100
fce917
osc
(dBc/Hz) -105
-110
-115
-120
40
140
240
340
440
540
640
740
840 fRF (MHz)
940
Fig 10. 100 kHz phase noise typical performance in digital application (Figure 27 and 28)
-80
fce918
osc
(dBc/Hz) -85
-90
-95
-100
-105
40
140
240
340
440
540
640
740
840 fRF (MHz)
940
Fig 11. 1 kHz phase noise typical performance in hybrid application (Figure 29 and 30)
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
32 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
-80
fce919
osc
(dBc/Hz) -85
-90
-95
-100
-105
40
140
240
340
440
540
640
740
840 fRF (MHz)
940
Fig 12. 10 kHz phase noise typical performance in hybrid application (Figure 29 and 30)
-100
fce920
osc
(dBc/Hz) -105
-110
-115
-120
40
140
240
340
440
540
640
740
840 fRF (MHz)
940
Fig 13. 100 kHz phase noise typical performance in hybrid application (Figure 29 and 30)
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
33 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
signal 50 source
LBIN or MBIN V 50
IFOUTA
27 spectrum analyzer Vo V'meas 50
e
Vmeas
DUT
Vi IFOUTB
RMS voltmeter
VCCA
fce747
Zi >> 50 Vi = 2 x Vmeas = 70 dBV. Vi = Vmeas + 6 dB = 70 dBV. Vo = V'meas + 3.75 dB.
Vo G v = 20 log ----Vi
DVB-T and PAL. IF = 38.9 MHz.
Fig 14. Gain (GV) measurement in low and mid band with asymmetrical IF output
signal 50 source
LBIN or MBIN V 50
IFOUTA
transformer spectrum analyzer C N1 Vo N2 V'meas 50
e
Vmeas
DUT
Vi IFOUTB
RMS voltmeter
fce748
Zi >> 50 Vi = 2 x Vmeas = 70 dBV. Vi = Vmeas + 6 dB = 70 dBV. Vo = V'meas + 15 dB (transformer ratio N1/N2 = 5 and transformer loss).
Vo G v = 20 log ----Vi
N1 = 10 turns. N2 = 2 turns. N1/N2 = 5. DVB-T and PAL. IF = 38.9 MHz.
Fig 15. Gain (GV) measurement in low and mid band with symmetrical IF output
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
34 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
NOISE SOURCE
BNC
RIM
LBIN or MBIN
27 IFOUTA
NOISE FIGURE METER
INPUT CIRCUIT
DUT
IFOUTB VCCA
fce750
NF = NFmeas - loss of input circuit (dB).
Fig 16. Noise figure (NF) measurement in low and mid band with asymmetrical IF output
BNC connector Cs
Cc
TL
to the IC mixer input
BNC connector
Ls
Cc
TL
to the IC mixer input
Lp
Cp
Lp
Cp
mce452
a. Schematic 1
For fRF = 50 MHz (Schematic 1) Loss = 0 dB. Cs = 12 pF in parallel with a 0.8 pF to 8 pF trimmer. Cp = 18 pF in parallel with a 0.8 pF to 8 pF trimmer. Cc = 4.7 nF. Lp = 8 turns, 5 mm, wire = 0.4 mm air coil TL = 50 semi rigid cable, length = 75 mm. For fRF = 150 MHz (Schematic 1) Loss = 0 dB. Cs = 0.8 pF to 8 pF trimmer. Cp = 0.4 pF to 2.5 pF trimmer. Cc = 4.7 nF. Lp = 4 turns, 4.5 mm, wire = 0.4 mm air coil TL = 50 semi rigid cable, length = 75 mm.
b. Schematic 2
For fRF = 300 MHz (Schematic 2) Loss = 0.5 dB. Cp = 8.2 pF in parallel with a 0.8 pF to 8 pF trimmer. Cc = 4.7 nF. Ls = 2 turns, 1.5 mm, wire = 0.4 mm air coil. Lp = 2 turns, 1.5 mm, wire = 0.4 mm air coil. TL = 50 semi rigid cable, length = 75 mm.
Fig 17. Input circuit for optimum noise figure in low and mid band
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
35 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
FILTER
50
AM = 30% 1 kHz A C unwanted signal source
eu
LBIN IFOUTA or MBIN
27
10 dB attenuator modulation analyzer
HYBRID
DUT
IFOUTB
50
Vo
38.9 MHz V Vmeas
50
50
B ew wanted signal source
D
VCCA
RMS voltmeter
fce749
Vo = Vmeas + 3.75 dB. Wanted signal source at fRFpix is 80 dBV. Unwanted output signal at fsnd. The level of unwanted signal is measured by causing 0.3 % AM modulation in the wanted signal.
Fig 18. Cross modulation measurement in low and mid band with asymmetrical IF output
FILTER
50
AM = 30% 1 kHz A C unwanted signal source
eu
LBIN or MBIN
transformer IFOUTA
6 dB attenuator modulation analyzer
HYBRID
DUT
IFOUTB
50
C
N1 Vo
N2 V V'meas
38.9 MHz
50
50
B ew wanted signal source
D
RMS voltmeter
fce793
V'meas = Vo - (transformer ratio N1/N2 = 5 and loss). Wanted signal source at fRFpix is 80 dBV. The level of unwanted signal Vo at fsnd is measured by causing 0.3 % AM modulation in the wanted output signal. N1 = 10 turns. N2 = 2 turns. N1/N2 = 5.
Fig 19. Cross modulation measurement in low and mid band with symmetrical IF output
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
36 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
signal 50 source A C HBIN1 IFOUTA
27 spectrum analyzer Vo V'meas 50
e
Vmeas
V
50
Vi
HYBRID
DUT
HBIN2 IFOUTB
B RMS voltmeter 50
D
VCCA
fce751
Loss in hybrid = 1 dB. Vi = Vmeas - loss = 70 dBV. Vo = V'meas + 3.75 dB.
Vo G v = 20 log ----- . Vi
DVB-T and PAL. IF = 38.9 MHz.
Fig 20. Gain (GV) measurement in high band with asymmetrical IF output
signal 50 source A C HBIN1 IFOUTA
transformer spectrum analyzer C N1 Vo N2 V'meas 50
e
Vmeas
V
50
Vi
HYBRID
DUT
B RMS voltmeter 50
D
HBIN2
IFOUTB
fce752
Loss in hybrid = 1 dB. Vi = Vmeas - loss = 70 dBV. Vo = V'meas + 15 dB (transformer ratio N1/N2 = 5 and transformer loss).
Vo G v = 20 log ----- . Vi
DVB-T and PAL. IF = 38.9 MHz.
Fig 21. Gain (GV) measurement in high band with symmetrical IF output
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
37 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
NOISE SOURCE
A
27 C HBIN1 IFOUTA
NOISE FIGURE METER
HYBRID B 50 D
DUT
HBIN2 IFOUTB
VCCA
fce753
Loss in hybrid = 1 dB. NF = NFmeas - loss.
Fig 22. Noise figure (NF) measurement in high band with asymmetrical IF output
FILTER
50
AM = 30% 1 kHz A C A C HBIN1 IFOUTA unwanted signal source
27
10 dB attenuator modulation analyzer
eu
HYBRID
HYBRID
DUT
HBIN2 IFOUTB
Vo
38.9 MHz V Vmeas
50
50
B ew wanted signal source
D
50 50
B
D
VCCA
RMS voltmeter
fce754
Wanted signal source at fRFpix is 70 dBV. Unwanted output signal at fsnd. The level of unwanted signal is measured by causing 0.3 % AM modulation in the wanted signal.
Fig 23. Cross modulation measurement in high band with asymmetrical IF output
AM = 30% 1 kHz 50 eu unwanted signal source
transformer A C A C HBIN1 IFOUTA
6 dB attenuator
FILTER
modulation analyzer C N1 Vo N2 V V'meas 38.9 MHz
50
HYBRID
HYBRID
DUT
HBIN2 IFOUTB
50
B wanted signal source
D
50 50
B
D
ew
RMS voltmeter
fce794
V'meas = Vo - (transformer ratio N1/N2 = 5 and loss) The level of unwanted signal is measured by causing 0.3 % AM modulation in the wanted signal. N1 = 10 turns. N2 = 2 turns. N1/N2 = 5.
Fig 24. Cross modulation measurement in high band with symmetrical IF output
9397 750 14178 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
38 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
signal 50 source
LBIN or MBIN V 50
IFOUTA
27 spectrum analyzer 50
e
Vmeas
DUT
IFOUTB
RMS voltmeter
VCCA
fce755
Zi >> 50 Vi = 2 x Vmeas. Vi = Vmeas + 6 dB.
Fig 25. Maximum RF input level without lock-out in low and mid band with asymmetrical IF output
signal 50 source A C HBIN1 IFOUTA
27 spectrum analyzer 50
e
Vmeas
V
50
Vi
HYBRID HBIN2
DUT
IFOUTB VCCA
B RMS voltmeter 50
D
fce756
Loss in hybrid = 1 dB. Vi = Vmeas - loss.
Fig 26. Maximum RF input level without lock-out in high band with asymmetrical IF output
12.1 PLL loop stability of measurement circuit
The TDA6650TT; TDA6651TT PLL loop stability is guaranteed in the configuration of Figure 27, 28, 29 and 30. In this configuration, the external supply source is 30 V minimum, the pull-up resistor R19, is 15 k and all of the local oscillators are aligned to operate at a maximum tuning voltage of 26 V. If the configuration is changed, there might be an impact on the loop stability. For any other configurations, a stability analysis must be performed. The conventional PLL AC model (cf. SIMPATA Philips software) used for the stability analysis, is valid provided the external source (DC supply source or DC-to-DC converter) is able to deliver a minimum current that is equal to the charge pump current in use.
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
39 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
The delivered current can be simply calculated with the following formula: V DC - V T I delivered = ------------------------ > I CP where: R pu Idelivered is the delivered current. VDC is the supply source voltage or DC-to-DC converter output voltage. VT is the tuning voltage. Rpu is the pull-up resistor between the DC supply source (or the DC-to-DC converter output) and the tuning line (R19 in Figure 27 to 30). ICP is the charge pump current in use.
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
40 of 54
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Product data sheet Rev. 04 -- 8 December 2004
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. 9397 750 14178
Philips Semiconductors
J4 LOW
J3 MID
J1 HIGH1
J2 HIGH2
C7 1.8 pF N750 C6
L3 140 nH R08304 D1 BB182 C5 47 pF N750
R1 12
6 L4 TOKO 500 nH 1 C27 12 pF 2
4
C4 4.7 nF
C3 4.7 nF
C1 4.7 nF
C2 4.7 nF
1.5 pF N750
R2 1 k
* 6t
2 3 C26 12 pF HBIN1 HBIN2 MBIN LBIN RFGND IFFIL1 IFFIL2 BS4 AGC BS3 BS2 BS1 BVS ADC/BS5 SCL SDA AS XTOUT XTAL1 R9 330 5 V bus R10 330 R11 330 1 (38) (1) 38 2 (37) (2) 37 3 (36) (3) 36 4 (35) (4) 35 5 (34) (5) 34 6 (33) (6) 33 7 (32) (7) 32 TDA6650TT (8) 31 8 (31) (TDA6651TT) 9 (30) (9) 30 10 (29) (10) 29 11 (28) (11) 28 12 (27) (12) 27 13 (26) (13) 26 14 (25) (14) 25 15 (24) (15) 24 16 (23) (16) 23 17 (22) (17) 22 18 (21) (18) 21 19 (20) (19) 20 C19 18 pF Y1 4 MHz LOSCIN LOSCOUT OSCGND MOSCIN2 MOSCIN1 HOSCIN2 HOSCOUT2 HOSCOUT1 HOSCIN1 IFGND IFOUTA IFOUTB VCCA PLLGND VCCD CP VT n.c. XTAL2 VCC C15 4.7 nF C16 4.7 nF R13 6.8 k 30 V C29 4.7 nF C31 10 F C32 10 F C30 10 F VCC L1 25 nH
C34 120 pF N750 C33 120 pF N750
R3 5.6 k D2 BB178 R4 5.6 k
C11 1 pF N750 C12 1 pF N750 C13 1 pF N750 C14 1 pF N750
TP1
AGC C28 150 nF D4 R20 1 k D5 R21 1 k D6 R22 1 k D7 R23 1 k D8 R24 1 k VCC R14 ST1 1 k J8 123456 SCL ST2 ADC R27 3.3 k R28 3.3 k SDA AS
D3 BB179 L2 13 nH R01255 C18 R6 27 R5 5.6 k 15 pF N470 R8 5.6 k C17 2.7 nF
5 V mixer/oscillator and low noise PLL synthesizer
TDA6650TT; TDA6651TT
VCC C21 100 nF C20 330 pF C23 4.7 nF R7 1 k
5 V bus VCC
1234 J5
R19 15 k J6
R26 27
J7 test 5 V bus 30 V
IF out
mce162
The pin numbers in parenthesis represent the TDA6651TT.
41 of 54
Fig 27. Measurement circuit for digital application, with asymmetrical IF output and DVB-T compliant loop filter
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Product data sheet Rev. 04 -- 8 December 2004
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. 9397 750 14178
Philips Semiconductors
J4 LOW
J3 MID
J1 HIGH1
J2 HIGH2
C7 1.8 pF N750 C6
L3 140 nH R08304 D1 BB182 C5 47 pF N750
R1 12
6 L4 TOKO 500 nH 1 C27 12 pF 2 * 6t
4
C4 4.7 nF
C3 4.7 nF
C1 4.7 nF
C2 4.7 nF
1.5 pF N750
R2 1 k
C34 HBIN1 HBIN2 MBIN LBIN RFGND IFFIL1 IFFIL2 BS4 AGC BS3 BS2 BS1 BVS ADC/BS5 SCL SDA AS XTOUT XTAL1 R9 330 5 V bus R10 330 R11 330 (1) 38 1 (38) (2) 37 2 (37) (3) 36 3 (36) (4) 35 4 (35) (5) 34 5 (34) (6) 33 6 (33) (7) 32 7 (32) TDA6650TT (8) 31 8 (31) (TDA6651TT) (9) 30 9 (30) (10) 29 10 (29) (11) 28 11 (28) (12) 27 12 (27) (13) 26 13 (26) (14) 25 14 (25) (15) 24 15 (24) (16) 23 16 (23) (17) 22 17 (22) (18) 21 18 (21) (19) 20 19 (20) C19 18 pF Y1 4 MHz LOSCIN LOSCOUT OSCGND MOSCIN2 MOSCIN1 HOSCIN2 HOSCOUT2 HOSCOUT1 HOSCIN1 IFGND IFOUTA IFOUTB VCCA PLLGND VCCD CP VT n.c. XTAL2 VCC C15 4.7 nF C16 4.7 nF R13 6.8 k VCC 120 pF N750 C33 120 pF N750
R3 5.6 k D2 BB178 R4 5.6 k
2
3 C26 12 pF
L1 25 nH
C11 1 pF N750 C12 1 pF N750 C13 1 pF N750 C14 1 pF N750
TP1
AGC C28 150 nF D4 R20 1 k D5 R21 1 k D6 R22 1 k D7 R23 1 k D8 R24 1 k VCC R14 ST1 1 k J8 123456 SCL ST2 ADC R27 3.3 k R28 3.3 k SDA AS
D3 BB179 L2 13 nH R01255 C18 R6 27 R5 5.6 k 15 pF N470 R8 5.6 k C17 2.7 nF
5 V mixer/oscillator and low noise PLL synthesizer
TDA6650TT; TDA6651TT
C21 100 nF
C24 4.7 nF
C23 4.7 nF C25 12 pF 1 2 3
R7 1 k
C20 330 pF
5 V bus VCC 30 V C29 4.7 nF C31 10 F C32 10 F C30 10 F TOKO 7451 1234 J5 6 R19 15 k J6 test 5 V bus 30 V IF out
fce875
4
J7
42 of 54
The pin numbers in parenthesis represent the TDA6651TT.
Fig 28. Measurement circuit for digital application, with symmetrical IF output and DVB-T compliant loop filter
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Product data sheet Rev. 04 -- 8 December 2004
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. 9397 750 14178
Philips Semiconductors
J4 LOW
J3 MID
J1 HIGH1
J2 HIGH2
C7 1.8 pF N750 C6
L3 140 nH R08304 D1 BB182 C5 47 pF N750
R1 12
6 L4 TOKO 500 nH 1 C27 12 pF 2 * 6t
4
C4 4.7 nF
C3 4.7 nF
C1 4.7 nF
C2 4.7 nF
1.5 pF N750
R2 1 k
C34 HBIN1 HBIN2 MBIN LBIN RFGND IFFIL1 IFFIL2 BS4 AGC BS3 BS2 BS1 BVS ADC/BS5 SCL SDA AS XTOUT XTAL1 R9 330 5 V bus R10 330 R11 330 (1) 38 1 (38) (2) 37 2 (37) (3) 36 3 (36) (4) 35 4 (35) (5) 34 5 (34) (6) 33 6 (33) (7) 32 7 (32) TDA6650TT (8) 31 8 (31) (TDA6651TT) (9) 30 9 (30) (10) 29 10 (29) (11) 28 11 (28) (12) 27 12 (27) (13) 26 13 (26) (14) 25 14 (25) (15) 24 15 (24) (16) 23 16 (23) (17) 22 17 (22) (18) 21 18 (21) (19) 20 19 (20) C19 18 pF Y1 4 MHz LOSCIN LOSCOUT OSCGND MOSCIN2 MOSCIN1 HOSCIN2 HOSCOUT2 HOSCOUT1 HOSCIN1 IFGND IFOUTA IFOUTB VCCA PLLGND VCCD CP VT n.c. XTAL2 VCC C15 4.7 nF C16 4.7 nF R13 1.8 k 30 V C29 4.7 nF C31 10 F C32 10 F C30 10 F R19 15 k VCC 120 pF N750 C33 120 pF N750
R3 5.6 k D2 BB178 R4 5.6 k
2
3 C26 12 pF
L1 25 nH
C11 1 pF N750 C12 1 pF N750 C13 1 pF N750 C14 1 pF N750
TP1
AGC C28 150 nF D4 R20 1 k D5 R21 1 k D6 R22 1 k D7 R23 1 k D8 R24 1 k VCC R14 ST1 1 k J8 123456 SCL ST2 ADC R27 3.3 k R28 3.3 k SDA AS
D3 BB179 L2 13 nH R01255 C18 R6 27 R5 5.6 k 15 pF N470 R8 5.6 k C17 4.7 nF
5 V mixer/oscillator and low noise PLL synthesizer
TDA6650TT; TDA6651TT
VCC C21 100 nF C20 2.7 nF C23 4.7 nF R7 1 k
5 V bus VCC
1234 J5
R26 27 J6
J7 5 V bus
test
30 V
IF out
fce909
43 of 54
The pin numbers in parenthesis represent the TDA6651TT.
Fig 29. Measurement circuit for hybrid application, with asymmetrical IF output and loop filter for PAL and DVB-T standards
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Product data sheet Rev. 04 -- 8 December 2004
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. 9397 750 14178
Philips Semiconductors
J4 LOW
J3 MID
J1 HIGH1
J2 HIGH2
C7 1.8 pF N750 C6
L3 140 nH R08304 D1 BB182 C5 47 pF N750
R1 12
6 L4 TOKO 500 nH 1 C27 12 pF 2 * 6t
4
C4 4.7 nF
C3 4.7 nF
C1 4.7 nF
C2 4.7 nF
1.5 pF N750
R2 1 k
C34 HBIN1 HBIN2 MBIN LBIN RFGND IFFIL1 IFFIL2 BS4 AGC BS3 BS2 BS1 BVS ADC/BS5 SCL SDA AS XTOUT XTAL1 R9 330 5 V bus R10 330 R11 330 (1) 38 1 (38) (2) 37 2 (37) (3) 36 3 (36) (4) 35 4 (35) (5) 34 5 (34) (6) 33 6 (33) (7) 32 7 (32) TDA6650TT (8) 31 8 (31) (TDA6651TT) (9) 30 9 (30) (10) 29 10 (29) (11) 28 11 (28) (12) 27 12 (27) (13) 26 13 (26) (14) 25 14 (25) (15) 24 15 (24) (16) 23 16 (23) (17) 22 17 (22) (18) 21 18 (21) (19) 20 19 (20) C19 18 pF Y1 4 MHz LOSCIN LOSCOUT OSCGND MOSCIN2 MOSCIN1 HOSCIN2 HOSCOUT2 HOSCOUT1 HOSCIN1 IFGND IFOUTA IFOUTB VCCA PLLGND VCCD CP VT n.c. XTAL2 VCC C15 4.7 nF C16 4.7 nF R13 1.8 k VCC 120 pF N750 C33 120 pF N750
R3 5.6 k D2 BB178 R4 5.6 k
2
3 C26 12 pF
L1 25 nH
C11 1 pF N750 C12 1 pF N750 C13 1 pF N750 C14 1 pF N750
TP1
AGC C28 150 nF D4 R20 1 k D5 R21 1 k D6 R22 1 k D7 R23 1 k D8 R24 1 k VCC R14 ST1 1 k J8 123456 SCL ST2 ADC R27 3.3 k R28 3.3 k SDA AS
D3 BB179 L2 13 nH R01255 C18 R6 27 R5 5.6 k 15 pF N470 R8 5.6 k C17 4.7 nF
5 V mixer/oscillator and low noise PLL synthesizer
TDA6650TT; TDA6651TT
C21 100 nF
C24 4.7 nF
C23 4.7 nF C25 12 pF 1 2 3
R7 1 k
C20 2.7 nF
5 V bus VCC 30 V C29 4.7 nF C31 10 F C32 10 F C30 10 F TOKO 7451 1234 J5 6 R19 15 k J6 test 5 V bus 30 V IF out
fce910
4
J7
44 of 54
The pin numbers in parenthesis represent the TDA6651TT.
Fig 30. Measurement circuit for hybrid application, with symmetrical IF output and loop filter for PAL and DVB-T standards
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
13. Application information
13.1 Tuning amplifier
The tuning amplifier is capable of driving the varicap voltage without an external transistor. The tuning voltage output must be connected to an external load of 15 k which is connected to the tuning voltage supply rail. The loop filter design depends on the oscillator characteristics and the selected reference frequency as well as the required PLL loop bandwidth. Applications with the TDA6650TT; TDA6651TT have a large loop bandwidth, in the order of a few tens of kHz. The calculation of the loop filter elements has to be done for each application, it depends on the reference frequency and charge pump current. A simulation of the loop can easily be done using the SIMPATA software from Philips.
13.2 Crystal oscillator
The TDA6650TT; TDA6651TT needs to be used with a 4 MHz crystal in series with a capacitor with a typical value of 18 pF, connected between pin XTAL1 and pin XTAL2. Philips crystal 4322 143 04093 is recommended. When choosing a crystal, take care to select a crystal able to withstand the drive level of the TDA6650TT; TDA6651TT without suffering from accelerated ageing. For optimum performances, it is highly recommended to connect the 4 MHz crystal without any serial resistance. The crystal oscillator of the TDA6650TT; TDA6651TT should not be driven (forced) from an external signal. Do not use the signal on pin XTAL1 or pin XTAL2, or the signal present on the crystal, to drive an external IC or for any other use as this may dramatically degrade the phase noise performance of the TDA6650TT; TDA6651TT.
13.3 Examples of I2C-bus program sequences
Table 22 to 29 show various sequences where: S = START A = acknowledge P = STOP. The following conditions apply: LO frequency is 800 MHz fcomp = 166.666 kHz N = 4800 BS3 output port is on and all other ports are off: thus the high band is selected Charge pump current ICP = 280 A Normal mode, with XTOUT buffer on IAGC = 220 nA AGC take-over point is set to 112 dBV (p-p) Address selection is adjusted to make address C2 valid.
9397 750 14178 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
45 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
To fully program the device, either sequence of Table 22 or 23 can be used, while other arrangements of the bytes are also possible.
Table 22: Start S
[1] [2]
Complete sequence 1 Divider byte 1 12 A Divider byte 2 C0 A Control byte 1 [1] CA A Control byte 2 A4 A Control byte 1 [2] 84 A Stop P
Address byte C2 A
Control byte 1 with bit T/A = 1, to program test bits T2, T1 and T0 and reference divider ratio bits R2, R1 and R0. Control byte 1 with bit T/A = 0, to program AGC time constant bit ATC and AGC take-over point bits AL2, AL1 and AL0.
Table 23: Start S
[1] [2]
Complete sequence 2 Control byte 1 [1] CA A Control byte 2 A4 A Divider byte 1 12 A Divider byte 2 C0 A Control byte 1 [2] 84 A Stop P
Address byte C2 A
Control byte 1 with bit T/A = 1, to program test bits T2, T1 and T0 and reference divider ratio bits R2, R1 and R0. Control byte 1 with bit T/A = 0, to program AGC time constant bit ATC and AGC take-over point bits AL2, AL1 and AL0.
Table 24: Start S Table 25: Start S
[1]
Sequence to program only the main divider ratio Address byte C2 A Divider byte 1 12 A Divider byte 2 C0 A Stop P
Sequence to change the charge pump current, the ports and the test mode. If the reference divider ratio is changed, it is necessary to send the DB1 and DB2 bytes Address byte C2 A Control byte 1 [1] CA A Control byte 2 A4 A Stop P
Control byte 1 with bit T/A = 1, to program test bits T2, T1 and T0 and reference divider ratio bits R2, R1 and R0.
Table 26: Start S
[1]
Sequence to change the test mode. If the reference divider ratio is changed, it is necessary to send the DB1 and DB2 bytes Address byte C2 A Control byte 1 [1] CA A Stop P
Control byte 1 with bit T/A = 1, to program test bits T2, T1 and T0 and reference divider ratio bits R2, R1 and R0.
Table 27: Start S
[1]
Sequence to change the charge pump current, the ports and the AGC data Address byte C2 A Control byte 1 [1] 82 A Control byte 2 A4 A Stop P
Control byte 1 with bit T/A = 0, to program AGC time constant bit ATC and AGC take-over point bits AL2, AL1 and AL0.
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
46 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
Sequence to change only the AGC data Address byte C2 A Control byte 1 [1] 84 A Stop P
Table 28: Start S
[1]
Control byte 1 with bit T/A = 0, to program AGC time constant bit ATC and AGC take-over point bits AL2, AL1 and AL0.
Table 29:
Sequence to program the main divider, the ALBC on and the test modes in normal mode with XTOUT buffer off Divider byte 1 12 A Divider byte 2 C0 A Control byte 1 [1] DA A Control byte 2 00 A Control byte 1 C2 A Stop P
Start Address byte S
[1]
C2
A
Control byte 1 with bit T/A = 1, to program test bits T2, T1 and T0 and reference divider ratio bits R2, R1 and R0.
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
47 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
14. Package outline
TSSOP38: plastic thin shrink small outline package; 38 leads; body width 4.4 mm; lead pitch 0.5 mm
SOT510-1
D
E
A X
c y HE vMA
Z
38
20
A2 pin 1 index A1
(A 3)
A
Lp L
1
e bp
19
wM
detail X
0
2.5 scale
5 mm
DIMENSIONS (mm are the original dimensions). UNIT mm A max. 1.1 A1 0.15 0.05 A2 0.95 0.85 A3 0.25 bp 0.27 0.17 c 0.20 0.09 D (1) 9.8 9.6 E (2) 4.5 4.3 e 0.5 HE 6.4 L 1 Lp 0.7 0.5 v 0.2 w 0.08 y 0.08 Z (1) 0.49 0.21
8 o 0
o
Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT510-1 REFERENCES IEC JEDEC JEITA EUROPEAN PROJECTION
ISSUE DATE 98-09-16 03-02-18
Fig 31. Package outline SOT510-1 (TSSOP38)
9397 750 14178 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
48 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
15. Handling information
Inputs and outputs are protected against electrostatic discharge in normal handling. However, to be completely safe, it is desirable to take normal precautions appropriate to handling integrated circuits.
16. Soldering
16.1 Introduction to soldering surface mount packages
This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our Data Handbook IC26; Integrated Circuit Packages (document order number 9398 652 90011). There is no soldering method that is ideal for all surface mount IC packages. Wave soldering can still be used for certain surface mount ICs, but it is not suitable for fine pitch SMDs. In these situations reflow soldering is recommended.
16.2 Reflow soldering
Reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement. Driven by legislation and environmental forces the worldwide use of lead-free solder pastes is increasing. Several methods exist for reflowing; for example, convection or convection/infrared heating in a conveyor type oven. Throughput times (preheating, soldering and cooling) vary between 100 seconds and 200 seconds depending on heating method. Typical reflow peak temperatures range from 215 C to 270 C depending on solder paste material. The top-surface temperature of the packages should preferably be kept:
* below 225 C (SnPb process) or below 245 C (Pb-free process)
- for all BGA, HTSSON..T and SSOP..T packages - for packages with a thickness 2.5 mm - for packages with a thickness < 2.5 mm and a volume 350 mm3 so called thick/large packages.
* below 240 C (SnPb process) or below 260 C (Pb-free process) for packages with a
thickness < 2.5 mm and a volume < 350 mm3 so called small/thin packages. Moisture sensitivity precautions, as indicated on packing, must be respected at all times.
16.3 Wave soldering
Conventional single wave soldering is not recommended for surface mount devices (SMDs) or printed-circuit boards with a high component density, as solder bridging and non-wetting can present major problems. To overcome these problems the double-wave soldering method was specifically developed. If wave soldering is used the following conditions must be observed for optimal results:
9397 750 14178 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
49 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
* Use a double-wave soldering method comprising a turbulent wave with high upward
pressure followed by a smooth laminar wave.
* For packages with leads on two sides and a pitch (e):
- larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be parallel to the transport direction of the printed-circuit board; - smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the transport direction of the printed-circuit board. The footprint must incorporate solder thieves at the downstream end.
* For packages with leads on four sides, the footprint must be placed at a 45 angle to
the transport direction of the printed-circuit board. The footprint must incorporate solder thieves downstream and at the side corners. During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured. Typical dwell time of the leads in the wave ranges from 3 seconds to 4 seconds at 250 C or 265 C, depending on solder material applied, SnPb or Pb-free respectively. A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications.
16.4 Manual soldering
Fix the component by first soldering two diagonally-opposite end leads. Use a low voltage (24 V or less) soldering iron applied to the flat part of the lead. Contact time must be limited to 10 seconds at up to 300 C. When using a dedicated tool, all other leads can be soldered in one operation within 2 seconds to 5 seconds between 270 C and 320 C.
16.5 Package related soldering information
Table 30: Package [1] BGA, LBGA, LFBGA, SQFP, SSOP..T [3], TFBGA, VFBGA, XSON DHVQFN, HBCC, HBGA, HLQFP, HSO, HSOP, HSQFP, HSSON, HTQFP, HTSSOP, HVQFN, HVSON, SMS PLCC [5], SO, SOJ LQFP, QFP, TQFP SSOP, TSSOP, VSO, VSSOP CWQCCN..L [8],
[1]
Suitability of surface mount IC packages for wave and reflow soldering methods Soldering method Wave Reflow [2] suitable suitable not suitable not suitable [4]
HTSSON..T [3],
suitable not WQCCN..L [8] recommended [5] [6] not recommended [7] not suitable
suitable suitable suitable not suitable
PMFP [9],
For more detailed information on the BGA packages refer to the (LF)BGA Application Note (AN01026); order a copy from your Philips Semiconductors sales office.
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
50 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
[2]
All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the maximum temperature (with respect to time) and body size of the package, there is a risk that internal or external package cracks may occur due to vaporization of the moisture in them (the so called popcorn effect). For details, refer to the Drypack information in the Data Handbook IC26; Integrated Circuit Packages; Section: Packing Methods. These transparent plastic packages are extremely sensitive to reflow soldering conditions and must on no account be processed through more than one soldering cycle or subjected to infrared reflow soldering with peak temperature exceeding 217 C 10 C measured in the atmosphere of the reflow oven. The package body peak temperature must be kept as low as possible. These packages are not suitable for wave soldering. On versions with the heatsink on the bottom side, the solder cannot penetrate between the printed-circuit board and the heatsink. On versions with the heatsink on the top side, the solder might be deposited on the heatsink surface. If wave soldering is considered, then the package must be placed at a 45 angle to the solder wave direction. The package footprint must incorporate solder thieves downstream and at the side corners. Wave soldering is suitable for LQFP, QFP and TQFP packages with a pitch (e) larger than 0.8 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm. Wave soldering is suitable for SSOP, TSSOP, VSO and VSSOP packages with a pitch (e) equal to or larger than 0.65 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm. Image sensor packages in principle should not be soldered. They are mounted in sockets or delivered pre-mounted on flex foil. However, the image sensor package can be mounted by the client on a flex foil by using a hot bar soldering process. The appropriate soldering profile can be provided on request. Hot bar soldering or manual soldering is suitable for PMFP packages.
[3]
[4]
[5] [6] [7] [8]
[9]
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
51 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
17. Revision history
Table 31: Revision history Release date Data sheet status Product data sheet Change notice Doc. number Supersedes 9397 750 14178 TDA6650TT_6651TT_3 Document ID Modifications:
TDA6650TT_6651TT_4 20041208
* * * * * * * *
The format of this data sheet has been redesigned to comply with the new presentation and information standard of Philips Semiconductors Section 3: Note added to the applications list Table 10 on page 11: Notes 1 and 2 added Section 10: Table notes modified Figure 18, 19, 23 and 24: Replaced "1 % AM modulation" with "0.3 % AM modulation" Figure 20: Modified by adding V'meas Figure 24: Added figure note Figure 30: Changed value of C17 and R13 Product specification Preliminary specification 9397 750 13025 TDA6650TT_6651TT_2 9397 750 11854 TDA6650TT_6651TT_1 -
TDA6650TT_6651TT_3 20040322 TDA6650TT_6651TT_2 20030911 TDA6650TT_6651TT_1 20030717
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
52 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
18. Data sheet status
Level I II Data sheet status [1] Objective data Preliminary data Product status [2] [3] Development Qualification Definition This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN).
III
Product data
Production
[1] [2] [3]
Please consult the most recently issued data sheet before initiating or completing a design. The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status.
19. Definitions
Short-form specification -- The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition -- Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information -- Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification.
customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes -- Philips Semiconductors reserves the right to make changes in the products - including circuits, standard cells, and/or software - described or contained herein in order to improve design and/or performance. When the product is in full production (status `Production'), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified.
21. Licenses
Purchase of Philips I2C-bus components Purchase of Philips I2C-bus components conveys a license under the Philips' I2C-bus patent to use the components in the I2C-bus system provided the system conforms to the I2C-bus specification defined by Koninklijke Philips Electronics N.V. This specification can be ordered using the code 9398 393 40011.
20. Disclaimers
Life support -- These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors
22. Contact information
For additional information, please visit: http://www.semiconductors.philips.com For sales office addresses, send an email to: sales.addresses@www.semiconductors.philips.com
9397 750 14178
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 04 -- 8 December 2004
53 of 54
Philips Semiconductors
TDA6650TT; TDA6651TT
5 V mixer/oscillator and low noise PLL synthesizer
23. Contents
1 2 3 3.1 4 5 6 6.1 6.2 7 7.1 7.2 7.3 8 8.1 8.1.1 8.1.2 8.1.3 8.1.4 8.1.5 8.1.6 8.2 8.3 9 10 11 12 12.1 13 13.1 13.2 13.3 14 15 16 16.1 16.2 16.3 16.4 16.5 17 18 19 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Application summary . . . . . . . . . . . . . . . . . . . . 3 Ordering information . . . . . . . . . . . . . . . . . . . . . 3 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pinning information . . . . . . . . . . . . . . . . . . . . . . 5 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 5 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Functional description . . . . . . . . . . . . . . . . . . . 6 Mixer, oscillator and PLL (MOPLL) functions . . 6 I2C-bus voltage . . . . . . . . . . . . . . . . . . . . . . . . . 7 Phase noise, I2C-bus traffic and crosstalk . . . . 7 2C-bus protocol . . . . . . . . . . . . . . . . . . . . . . . . . 8 I Write mode; R/W = 0 . . . . . . . . . . . . . . . . . . . . 8 I2C-bus address selection. . . . . . . . . . . . . . . . 10 XTOUT output buffer and mode setting . . . . . 10 Step frequency setting . . . . . . . . . . . . . . . . . . 10 AGC detector setting . . . . . . . . . . . . . . . . . . . 11 Charge pump current setting . . . . . . . . . . . . . 11 Automatic Loop Bandwidth Control (ALBC) . . 12 Read mode; R/W = 1 . . . . . . . . . . . . . . . . . . . 13 Status at power-on reset. . . . . . . . . . . . . . . . . 14 Internal circuitry. . . . . . . . . . . . . . . . . . . . . . . . 15 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 19 Thermal characteristics. . . . . . . . . . . . . . . . . . 20 Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 21 PLL loop stability of measurement circuit . . . . 39 Application information. . . . . . . . . . . . . . . . . . 45 Tuning amplifier. . . . . . . . . . . . . . . . . . . . . . . . 45 Crystal oscillator . . . . . . . . . . . . . . . . . . . . . . . 45 Examples of I2C-bus program sequences . . . 45 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 48 Handling information. . . . . . . . . . . . . . . . . . . . 49 Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Introduction to soldering surface mount packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . 49 Wave soldering . . . . . . . . . . . . . . . . . . . . . . . . 49 Manual soldering . . . . . . . . . . . . . . . . . . . . . . 50 Package related soldering information . . . . . . 50 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 52 Data sheet status . . . . . . . . . . . . . . . . . . . . . . . 53 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 20 21 22 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Licenses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Contact information . . . . . . . . . . . . . . . . . . . . 53
(c) Koninklijke Philips Electronics N.V. 2004
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Date of release: 8 December 2004 Document number: 9397 750 14178
Published in The Netherlands

▲Up To Search▲

Price & Availability of TDA6650TDA6651

	To Download TDA6650TDA6651 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .